Atlas PVC strainer
Atlas PVC strainer From €495.00 – €645.00 VAT incl.
Back to products
Mountfield - Czech Republic

Pressure gauge 1/4″ 0–4 bar for sand filter

€44.96 VAT incl.

1/4″ pressure gauge with a 0–4 bar scale for sand filters. It shows the filter pressure and indicates when it is time to backwash.

  • 1/4″ connection
  • 0–4 bar scale (and in PSI)
  • Suitable for many filter models
+449 points in “Endless Summer” +1 000 bonus points on the second online purchase · terms

Frequently bought together

€44.96 VAT incl.
Total for selected:
Description
Pressure gauge for Mountfield sand filter · spare part for filtration

Pressure gauge 1/4″ 0–4 bar for sand filter

The pressure gauge for the Mountfield sand filter shows the pressure of the pool filter. This model has a 1/4″ connection and a 0–4 bar scale. It is suitable for many Mountfield sand filters.

The pressure rises when the sand gets dirty. That is why the pressure gauge is the simplest way to know when to backwash the filter. If the needle is too high, the water circulates with difficulty. If it is too low, there may be another cause.

Code UHEC27086EType: pressure gaugeConnection: 1/4″Scale: 0–4 bar
Filter pressure gauge 1/4″ with a 0–4 bar scale
Filter pressure gauge
Technical data
Manufacturer codeUHEC27086E
ManufacturerMountfield
Typepressure gauge
Connection1/4″
Scale0–4 bar
Suitable forsand filters for pools
Compatibility

Suitable for

  • 3BTE0065 – Praher Top 320 filter
  • 3BTE0066 – Praher VarioTop 350 filter
  • 3BTE0064 – SWP 5.5 m³/h sand filter
  • 3BTE0355, 3BTE0356, 3BTE0362, 3BTE0363 – PRO S144T, S166T, S210T, S210S sand filters
  • 3BTE0418, 3BTE0425 – G S144T and G S166T sand filters
  • 3BTE0415, 3BTE0416, 3BTE0417, 3BTE0426 – MAXFLO sand filters
  • 3BTE0244 – Azuro 9 m³/h sand filter

The list is abridged. If you cannot find your model, write to us and we will check compatibility.

All filter and equipment spare parts are in a single category, and you can see the complete solutions in sand filtration for pools. The pressure gauge fits filters such as the Azuro 9 m³/h sand filtration kit, and when replacing the valve you may also need the six-way valve for sand filter. The other accessories are in filter valves and parts.

When to replace the pressure gauge of the Mountfield sand filter

Replace the pressure gauge if the needle does not return to zero, the glass is misted or there is a leak around the thread. A damaged gauge gives wrong readings. You may then backwash the filter earlier or later than necessary. A new pressure gauge is an inexpensive investment.

  • 0–4 bar scale, with a second scale in PSI
  • 1/4″ connection with thread on the underside
  • Easy replacement
  • Manufacturer code UHEC27086E

How to fit the sand filter pressure gauge

First switch off the pump and release the pressure in the filter. Then unscrew the old pressure gauge. Clean the thread of the seat. Wrap the thread of the new pressure gauge with sealing tape. Screw it in by hand and finish tightening a little with a spanner. Finally, start the pump and check that there are no leaks.

Note the pressure after each backwash. This way you will know the normal value for your filter. When the needle rises about 0.5 bar above it, it is time to backwash. Do not overtighten the pressure gauge housing, because the unit may be damaged.

Not sure this is the right part for you?

Send us the model of your appliance and a photo of the old part. We will check compatibility before you place your order.

Technical data
About Mountfield - Czech Republic
Instructions
Delivery and warranty